How do I install Blue 92 Anti-Fracture Membrane or 9235 Waterproofing Membrane (as an anti-fracture membrane)?
9235 Waterproofing Membrane and Blue 92 Anti-Fracture Membrane are a cold-applied, liquid rubber polymers which are used with LATICRETE Waterproofing/Anti-Fracture Fabric. The liquid is applied with a paint roller or paint brush and the fabric is embedded into the liquid until the liquid bleeds through the fabric. A top coat of the membrane liquid is immediately applied over the fabric. LATASIL™ is applied at adjoining surfaces, drains connections and pipe penetrations.
Related Documents:
9235 Waterproofing Membrane DS 236.0
Blue 92 Anti-Fracture Membrane DS 647.0
How do I install HYDRO BAN® XP or HYDRO BAN as an anti-fracture membrane?
HYDRO BAN® XP and HYDRO BAN are cold-applied, liquid rubber polymer which is applied with a paint roller, paint brush or airless paint sprayer. No membrane reinforcing fabric is typically required. The first liquid coat must be completely dry to the touch prior to applying the second coat of membrane liquid. HYDRO BAN XP will change from a light green to a darker green when cured, and HYDRO BAN will change from a sage green color to an olive green color when dry. The second liquid coat can then be applied and must also dry to the touch. A LATICRETE Latex-fortified thin-set (e.g. 254 Platinum, 257 TITANIUM™, etc...) may be used to install most types of tile or stone directly to the HYDRO BAN XP or HYDRO BAN. Please refer to the HYDRO BAN XP or HYDRO BAN data sheet and Installation Instructions for more complete information.
Related Documents:
Spraying LATICRETE® HYDRO BAN® TDS 410
HYDRO BAN® XP DS 36642
HYDRO BAN DS 663.0
HYDRO BAN Installation Instructions DS 663.5
HYDRO BAN Installation Video Click Here
How do I install FRACTURE BAN™ 40 and FRACTURE BAN 90?
The FRACTURE BAN™ 40 and FRACTURE BAN 90 are pliable, light weight peel and stick membrane designed for use under thin-bed adhesives for ceramic tile, stone and other hard surface installations. FRACTURE BAN product is available in two (2) configurations; LRACTURE BAN 40 is 40 mil (1mm) thick and FRACTURE BAN 90 is 90 mil (2.3mm) thick. Properly prepared interior substrates to be treated with either FRACTURE BAN configuration must first be primed with FRACTURE BAN Primer. Measure the area and cut the FRACTURE BAN length 6” to 8” (152 to 203mm) longer than needed to allow for a trimmed fit. Lay FRACTURE BAN on surface with release liner side down. Pull release paper off membrane while hand smoothing ridges and air pockets to ensure 100% contact and good bond. Trim excess material as needed at wall, corners or terminations. Apply subsequent rolls in the same manner and ensure that the edges are butted together. Refer to product data sheet for more information, including for exterior applications (exterior applications require use of VAPOR BAN™ Primer ER in lieu of FRACTURE BAN Primer with FRACTURE BAN 40 only).
Related Documents:
FRACTURE BAN™ DS 155.0FRACTURE BAN Primer DS 156.0
VAPOR BAN Primer ER DS 35222
FRACTURE BAN Installation Instructions DS 013.3
FRACTURE BAN Installation Video – Click Here
How do I install FRACTURE BAN™ SC?
FRACTURE BAN™ SC is a thin, load bearing, self-curing liquid rubber polymer that can be easily applied in a single coat to form a flexible seamless anti-fracture membrane. Pre-treat cracks, joints, coves and floor/wall/transitions as stated in product data sheet. For the main application, install FRACTURE BAN SC onto properly prepared interior, horizontal substrates, using a paint brush or roller to apply a liberal coat (30 – 40 mils (0.75 – 1 mm) wet thickness. Use a wet film gauge to ensure proper wet mil thickness is achieved. Refer to product data sheet for more information.
Related Documents:
FRACTURE BAN™ SC DS 544.0What is the coverage of Blue 92 Anti-Fracture Membrane and 9235 Waterproofing Membrane?
One full unit consisting of 6 gallons (23 liters) of 9235 Waterproofing Membrane liquid and LATICRETE Waterproofing/Anti-Fracture Fabric will cover approximately 300 ft2(27m2).
One mini unit consisting of 2 gallons (7.6 liters) of 9235 Waterproofing Membrane liquid and LATICRETE Waterproofing/Anti-Fracture Fabric will cover approximately 75 ft2 (6.8m2).
Related Documents:
9235 Waterproofing Membrane DS 236.0
Blue 92 Anti-Fracture Membrane DS 647.0
Fabric Reinforced Membrane Installation Instructions DS WPAF.5
What is the coverage of HYDRO BAN® XP and HYDRO BAN;?
One full unit consisting of 5 gallons (19 liters) of HYDRO BAN® XP liquid will cover approximately 250 ft2(23.2m2).
One full unit consisting of 5 gallons (19 liters) of HYDRO BAN® liquid will cover approximately 250 ft2(23.2m2).
One mini unit consisting of 1 gallon (3.8 liters) of HYDRO BAN XP liquid will cover approximately 50 ft2(4.65m2).
One mini unit consisting of 1 gallon (3.8 liters) of HYDRO BAN liquid will cover approximately 50 ft2(4.65m2).
Related Documents:
HYDRO BAN® XP DS 36642
HYDRO BAN® DS 663.0
What is the coverage of FRACTURE BAN™ 40 and FRACTURE BAN 90?
One roll of FRACTURE BAN 40 will cover approximately 225 ft2(20.9m2).
One roll of FRACTURE BAN 90 will cover approximately 100 ft2(9.3m2).
One gallon (3.8 L) of diluted FRACTURE BAN Primer will cover approximately 285 ft2(26.5 m2).
Related Documents:
FRACTURE BAN™ DS 155.0FRACTURE BAN Primer DS 156.0
FRACTURE BAN Installation Instructions DS 013.3
What is the coverage of FRACTURE BAN™ SC?
One 3.5 gallon (13.2 L) bucket of FRACTURE BAN SC will cover approximately 175 ft2(16.2m2).
A One gallon (3.8 L) pail of FRACTURE BAN SC will cover approximately 50 ft2(4.6m2).
Related Documents:
FRACTURE BAN™ SC DS 544.0To what substrates can HYDRO BAN® XP;, HYDRO BAN, 9235 Waterproofing Membrane, FRACTURE BAN™, and FRACTURE BAN SC be directly applied?
Substrates common to HYDRO BAN® XP, HYDRO BAN, 9235 Waterproofing Membrane, FRACTURE BAN, and FRACTURE BAN SC are clean, structurally sound concrete, exterior glue plywood (interior applications only), masonry surfaces, cement backer boards, cement mortar beds, concrete and brick masonry, and cement plasters. For a more complete list of suitable substrates, please refer to the product data sheets of the individual LATICRETE membrane.
Related Documents:
HYDRO BAN® XP DS 36642HYDRO BAN DS 663.0
9235 Waterproofing Membrane DS 236.0
FRACTURE BAN™ DS 155.0
FRACTURE BAN Primer DS 156.0
FRACTURE BAN SC DS 544.0
How soon can I install 9235 Waterproofing Membrane or LATICRETE Blue 92 Anti-Fracture Membrane over:
New Concrete - minimum 14 days at 70°F (21°C)
Latex mortar beds - next day at 70°F (21°C)
Leveling or patching materials - allow a full 72 hour cure time at 70°F (21°C).
NOTE: Most importantly for all substrates above; the substrate moisture content must not exceed 5 lbs./1,000 ft2/24 hours (283µg/s•m2) when tested using the Calcium Chloride test (ASTM F1869) or 75% Relative Humidity (RH) when tested with moisture probes (ASTM F2170).
Related Documents:
9235 Waterproofing Membrane DS 236.0
Blue 92 Anti-Fracture Membrane DS 647.0
Fabric Reinforced Membranes Installation Instructions DS WPAF.5
How soon can I install HYDRO BAN® XP or HYDRO BAN over:
New Concrete - minimum 14 days at 70°F (21°C) and NOTE below.
Latex mortar beds - next day at 70°F (21°C) and NOTE below.
Leveling or patching materials - allow a full 72 hour cure time at 70°F (21°C) and NOTE below.
NOTE: Most importantly for all substrates above; the substrate moisture content must not exceed 5 lbs./1,000 ft2/24 hours (283µg/s•m2) when tested using the Calcium Chloride test (ASTM F1869) or 75% Relative Humidity (RH) when tested with moisture probes (ASTM F2170).
Related Documents:
HYDRO BAN XP DS 36642
HYDRO BAN DS 663.0
HYDRO BAN XP Installation Instructions DS 10003
HYDRO BAN Installation Instructions DS 663.5
How soon can I install FRACTURE BAN™ over:
New Concrete - minimum 14 days at 70°F (21°C) and NOTE below.Latex mortar beds - allow a full 72 hour minimum cure time at 70°F (21°C) and NOTE below.
Leveling or patching materials - allow a full 72 hour cure time at 70°F (21°C) and NOTE below.
NOTE: Most importantly for all substrates above; the substrate moisture content must not exceed 5 lbs./1,000 ft2/24 hours (283µg/s•m2) when tested using the Calcium Chloride test (ASTM F1869) or 75% Relative Humidity (RH) when tested with moisture probes (ASTM F2170).
Related Documents:
FRACTURE BAN™ DS 155.0FRACTURE BAN Primer DS 156.0
How soon can I install FRACTURE BAN™ SC over:
New Concrete - minimum 14 days at 70°F (21°C) and NOTE below.
Latex mortar beds - allow a full 72 hour minimum cure time at 70°F (21°C) and NOTE below.
Leveling or patching materials - allow a full 72 hour cure time at 70°F (21°C) and NOTE below.
NOTE: Most importantly for all substrates above; the substrate moisture content must not exceed 5 lbs./1,000 ft2/24 hours (283µg/s•m2) when tested using the Calcium Chloride test (ASTM F1869) or 75% Relative Humidity (RH) when tested with moisture probes (ASTM F2170).
Related Documents:
FRACTURE BAN™ SC DS 544.0What adhesives are acceptable for installing tile over HYDRO BAN® or HYDRO BAN, 9235 Waterproofing Membrane, Blue 92 Anti-Fracture Membrane, and FRACTURE BAN™ SC?
Adhesive options include:
NOTE: Use LATAPOXY® 300 Adhesive for chemical resistant installations and the installation of moisture sensitive stone. Requires LATICRETE® 9235 Waterproofing Membrane, LATICRETE Blue 92 Anti-Fracture Membrane and LATICRETE FRACTURE BAN™ SC to cure for a full 7 days, or, allow LATICRETE HYDRO BAN® XP or LATICRETE HYDRO BAN to cure for a minimum of 2 hours after the membrane has completely dried to the touch at 70°F (21°C), prior to installing tile or stone.
Related Documents:
HYDRO BAN® XP DS 36642
HYDRO BAN DS 663.0
LATAPOXY® 300 Adhesive DS 633.0
254 Platinum DS 677.0
254R Platinum Rapid DS 729.0
257 TITANIUM™ DS 292
MULTIMAX™ LITE DS 34082
Fabric Reinforced Membranes Installation Instructions DS WPAF.5
HYDRO BAN XP Installation Instructions DS 10003
HYDRO BAN Installation Instructions DS 663.5
What adhesives are acceptable for installing tile or stone over FRACTURE BAN™?
Adhesive options include:
*NOTE: Do not install moisture-sensitive tile or stone with water based setting materials on top of FRACTURE BAN peel & stick membranes. Also, dimensionally weak natural stone tile that normally would not be categorized as moisture sensitive; such as travertine, limestone, marble and agglomerates can exhibit doming, cupping or curing when wet-set using large, heavy tile mortar (e.g. medium bed mortar) methods of installation over impervious sheet membranes such as FRACTURE BAN. For this reason, areas requiring more than 3/8” (10 mm) buildup require the use of an NXT™ self-leveling underlayment or cured 3701 Fortified Mortar application before installation of FRACTURE BAN. When installing natural stone, always do a mock-up area of the proposed installation and allow materials to reach full cure to ensure achieving the desired effect.
Related Documents:
HYDRO BAN® XP DS 36642HYDRO BAN DS 663.0
LATAPOXY® 300 Adhesive DS 633.0
254 Platinum DS 677.0
254R Platinum Rapid DS 729.0
257 TITANIUM™ DS 292
MULTIMAX™ LITE DS 34082
FRACTURE BAN™ DS 155.0
FRACTURE BAN Primer DS 156.0
Can I use a mastic type adhesive to install tile over HYDRO BAN™ XP, HYDRO BAN, 9235 Waterproofing Membrane, FRACTURE BAN™ SC, or Blue 92 Anti-Fracture Membrane?
No. A latex or polymer fortified thin-set adhesive complying with ANSI A118.4 or ANSI A118.15 is required to properly bond tile or stone to a LATICRETE waterproofing and/or anti-fracture membrane. Epoxy adhesives complying with ANSI A118.3 (e.g. LATAPOXY® can also be used over LATICRETE anti-fracture membranes.
Related Documents:
HYDRO BAN® XP DS 36642
HYDRO BAN DS 663.0
9235 Waterproofing Membrane DS 236.0
FRACTURE BAN™ SC DS 544
Blue 92 Anti-Fracture Membrane DS 647.0
15 Premium Mastic DS 286
What is the warranty on HYDRO BAN® XP, HYDRO BAN, 9235 Waterproofing Membrane, and FRACTURE BAN&trade?
Labor and materials replacement for 25 years from date of installation when using the full LATICRETE System as outlined in the LATICRETE Systems Warranty (DS 025.0); otherwise, every LATICRETE product is backed by a one year product warranty (DS 230.13) when used solely as an individual component of a tile or stone installation, when used with LATICRETE products not listed on the warranty document, or when used with competitor's products. For other warranty options please visit http:www.laticrete.com/architects/warranties.aspx
Related Documents:
HYDRO BAN® XP DS 36642
HYDRO BAN DS 663.0
9235 Waterproofing Membrane DS 236.0
FRACTURE BAN™ DS 155.0
FRACTURE BAN Primer DS 156.0
LATICRETE 25-Year System Warranty DS 025.0
LATICRETE Product Warranty DS 230.13
What types of sealant are compatible with HYDRO BAN® XP, HYDRO BAN, 9235 Waterproofing Membrane, or FRACTURE BAN™ SC, and Blue 92 Anti-Fracture Membrane?
Use LATASIL™, a neutral cure, 100% silicone sealant which conforms to the following ASTM C920 standards; Type S, Grade NS, Class 25, Use NT, Use I, Use M, Use G. LATASIL also passes ASTM C794 Adhesion Properties.
Related Documents:
LATASIL™ DS 6200.1
HYDRO BAN® XP DS 36642
HYDRO BAN DS 663.0
9235 Waterproofing Membrane DS 236.0
FRACTURE BAN™ SC DS 544
Blue 92 Anti-Fracture Membrane DS 647.0
Fabric Reinforced Membranes Installation Instructions DS WPAF.5
HYDRO BAN XP Installation Instructions DS 10003
HYDRO BAN Installation Instructions DS 663.5
LATASIL Installation Video - Click Here
Can I install vinyl tile over HYDRO BAN® XP, HYDRO BAN, 9235 Waterproofing Membrane, FRACTURE BAN™ SC, and Blue 92 Anti-Fracture Membrane?
Yes - after the HYDRO BAN® XP. HYDRO BAN, 9235 Waterproofing Membrane, FRACTURE BAN™ SC, and Blue 92 Anti-Fracture Membrane is installed, use a latex based vinyl adhesive to adhere the vinyl tile to the membranes. Ensure that the adhesive contains no solvents. If there is a question as to the compatibility of the vinyl adhesive and the membrane, apply a continuous 1/8" (3mm) thick coating of a LATICRETE liquid latex thin-set mortar to the membrane and allow to harden. Then install the vinyl flooring.
Related Documents:
HYDRO BAN® XP DS 36642
HYDRO BAN DS 663.0
9235 Waterproofing Membrane DS 236.0
FRACTURE BAN™ SC DS 544
Blue 92 Anti-Fracture Membrane DS 647.0
Can I install HYDRO BAN® XP, HYDRO BAN, 9235 Waterproofing Membrane, FRACTURE BAN™ SC, and Blue 92 Anti-Fracture Membrane over plywood in exterior applications?
No, HYDRO BAN® XP, HYDRO BAN, 9235 Waterproofing Membrane, FRACTURE BAN™ SC, and Blue 92 Anti-Fracture Membrane are not intended for this installation. You must use the LATICRETE Plaza and Deck System for these applications.
Related Documents:
LATICRETE Drawing ES-F103
LATICRETE Drawing ES-F103b
LATICRETE Plaza and Deck System DS 290.0
Exterior Installation of Tile and Stone Over Occupied Space TDS 157
When can I install tile over HYDRO BAN®, 9235 Waterproofing Membrane, FRACTURE BAN™ SC or Blue 92 Anti-Fracture Membrane?
As soon as the final liquid coat is completely dry to the touch.
Related Documents:
HYDRO BAN DS 663.09235 Waterproofing Membrane DS 236.0
FRACTURE BAN SC DS 544.0
Blue 92 Anti-Fracture Membrane DS 647.0
When can I install tile over FRACTURE BAN™?
Tile can be applied immediately after installation of the FRACTURE BAN is complete.
Related Documents:
FRACTURE BAN™ DS 155.0FRACTURE BAN Installation Instructions DS 013.3