Waterproofing

When should you use a waterproofing membrane?

In general, you should always use a waterproofing membrane in any application where the intent is to keep water from penetrating into the substrate and eventually into ancillary spaces. These would include, but are not limited to, showers, bathrooms, steam rooms, swimming pools, spas, fountains, commercial kitchens, food preparation areas, and more… kitchen, wet/submerged area before tiling. LATICRETE® HYDRO BAN® XP, LATICRETE HYDRO BAN, LATICRETE HYDRO BAN Quick Cure, LATICRETE HYDRO BAN Sheet Membrane, LATICRETE HYDRO BAN Cementitious Waterproofing Membrane, LATICRETE 9235 Waterproofing Membrane, or LATICRETE HYDRO BARRIER™ Plus are ideal based on the suitability of the membrane for a particular application. For more information, please refer to the specific membrane product data sheet below or call LATICRETE Technical Services at 1.800.243.4788 x1235.

Can you tile over a waterproofing membrane?

Yes, if the waterproofing membrane is manufactured specifically to accept tile, stone or other adhered veneer. LATICRETE waterproofing membranes are manufactured for such applications on a wide variety of applications over a multitude of substrates. These membranes include LATICRETE® HYDRO BAN® XP, LATICRETE HYDRO BAN, LATICRETE HYDRO BAN Quick Cure, LATICRETE HYDRO BAN Sheet Membrane, LATICRETE HYDRO BAN Cementitious Waterproofing Membrane, LATICRETE 9235 Waterproofing Membrane, or LATICRETE HYDRO BARRIER™ Plus. Tile can be installed over these membranes using an ANSI A118.4, ANSI A118.15 or ANSI A118.3 adhesive. Please refer to the data sheet for a specific membrane below for more specific information.

Is a waterproofing membrane necessary?

If you are concerned about water penetration and leaks which can damage property or go places where water is not intended to be then the use of a waterproofing membrane is a very good idea. Many LATICRETE waterproofing membranes also have anti-fracture capabilities to help prevent the transfer of cracks in the substrate from transferring through the tile or stone and meet or exceed the requirements of ANSI A118.10 and ANSI A118.12.

How do I install HYDRO BAN®?

HYDRO BAN® is a cold-applied, liquid rubber polymer which is applied with a paint roller, paint brush or airless paint sprayer. No membrane reinforcing fabric is typically required. The first liquid coat must be completely dry to the touch prior to applying the second coat of membrane liquid. HYDRO BAN will change from a sage green color to an olive green color when dry. The second liquid coat can then be applied and must also dry to the touch. A LATICRETE latex-fortified thin-set (e.g. 257 Titanium, 254 Platinum, etc...) may be used to install most types of tile or stone directly to the HYDRO BAN. Please refer to the HYDRO BAN data sheet and HYDRO BAN Installation Instructions for more complete information. Please read the installation instructions for the complete information on how to properly prepare the substrate and install HYDRO BAN.

How do I install HYDRO BAN® XP?

HYDRO BAN® XP can be used for waterproofing and crack protection in a variety of interior and exterior spaces in residential, commercial and industrial settings. For use in indoor applications such as: steam showers and steam rooms, bathrooms, kitchens and food processing areas, countertops and facades. Plus it’s a perfect exterior waterproofing membrane for swimming pools, fountains/water features, spas and hot tubs, terraces and balconies (over unoccupied spaces). The first liquid coat must be completely dry to the touch prior to applying the second coat of membrane liquid. HYDRO BAN will change to a dark green color when dry. The second liquid coat can then be applied and must also dry to the touch. A LATICRETE latex-fortified thin-set (e.g. 257 Titanium, 254 Platinum, etc...) may be used to install most types of tile or stone directly to the HYDRO BAN XP. Please refer to the HYDRO BAN XP data sheet and HYDRO BAN XP Installation Instructions for more complete information. Please read the installation instructions for the complete information on how to properly prepare the substrate and install HYDRO BAN XP.

How do I install HYDRO BAN® Quick Cure?

HYDRO BAN® Quick Cure is a rapid, thin, liquid applied ready-to-use waterproofing membrane that is ANSI A118.10 compliant. For most applications, apply a 6 mil coat of HYDRO BAN Quick Cure liquid with brush or roller over substrate including pre-treated areas. Flash membrane up over pre-treated coves and corners, so such areas have two layers of HYDRO BAN Quick Cure liquid. Let dry 15 to 20 minutes at 70°F (21°C) and 50% RH. Apply another 6 mil coat of HYDRO BAN Quick Cure liquid over entire surface to seal membrane. When last coat has dried 15 to 20 minutes, inspect final surface for pinholes, voids, thin spots or other defects. Please read the installation instructions on the product data sheet for the complete information on how to properly prepare the substrate and install HYDRO BAN Quick Cure based on substrate type and application.

How do I install HYDRO BAN® Cementitious Waterproofing?

HYDRO BAN® Cementitious Waterproofing is a one component, polymer fortified, cement based waterproofing material that mixes with water. Apply a liberal coat (20 mil [0.5mm]) of HYDRO BAN Cementitious Waterproofing Membrane with brush or roller over substrate including pre-treated area. Once dry to the touch, apply another liberal coat (20 mil [0.5mm]) of HYDRO BAN Cementitious Waterproofing Membrane over the first coat. Let top coat dry to the touch, approximately 1–2 hours at 70°F (21°C) and 50% RH. When last coat has dried to the touch, inspect final surface for pinholes, voids, thin spots or other defects. Please read the installation instructions for the complete information on how to properly prepare the substrate and install HYDRO BAN Cementitious Waterproofing.

How do I install HYDRO BARRIER™ Plus?

HYDRO BARRIER™ Plus is a thin, load-bearing, selfcuring, liquid rubber polymer easily applied to form a flexible, seamless waterproofing, anti-fracture membrane that no longer requires the use of waterproofing fabric, when applied in coves and corners. Apply membrane and flood test the same day as soon as 12 hours* after final cure. Apply a liberal coat (15 – 22 mils [0.4 – 0.6 mm]) of HYDRO BARRIER Plus with brush or roller over substrate including pre-treated areas. Apply another liberal coat (15 – 22 mils [0.4 – 0.6 mm]) of HYDRO BARRIER Plus over the first coat of HYDRO BARRIER Plus. Let topcoat dry to the touch, approximately 1–3 hours at 70°F (21°C) and 50% RH. When last coat has dried to the touch, inspect final surface for pinholes, voids, thin spots or other defects. HYDRO BARRIER Plus will dry to a darker blue color when fully cured. Please read the installation instructions for the complete information on how to properly prepare the substrate and install HYDRO BARRIER Plus.

How do I install HYDRO BARRIER™?

HYDRO BARRIER™ is a thin, load bearing, self curing liquid rubber polymer which can be easily applied to form a flexible seamless waterproof/anti-fracture membrane. Apply a liberal coat (15 – 22 mils [0.4 – 0.6 mm]) of HYDRO BARRIER with brush or roller over substrate including pre-treated areas. Apply another liberal coat (15 – 22 mils [0.4 – 0.6 mm]) of HYDRO BARRIER over the first coat of HYDRO BARRIER. Let topcoat dry to the touch, approximately 1–3 hours at 70°F (21°C) and 50% RH. When last coat has dried to the touch, inspect final surface for pinholes, voids, thin spots or other defects. HYDRO BARRIER will dry to darker blue color when fully cured. Please read the installation instructions for the complete information on how to properly prepare the substrate and install HYDRO BARRIER.

How do I install HYDRO BAN Sheet Membrane?

HYDRO BAN Sheet Membrane is a high performance, low-perm waterproofing sheet membrane for use in interior, residential and commercial waterproofing applications including steam showers and steam rooms. This product is applied using a LATICRETE polymer-fortified thin-set mortar (e.g. 257 Titanium, 254 Platinum, etc…) and seams are treated with a polymer fortified thin-set mortar and HYDRO BAN Sheet Membrane Sealing Tape. Please read the installation instructions for the complete information on how to properly prepare the substrate and install HYDRO BAN Sheet Membrane.

What is the coverage of LATICRETE® Waterproofing Membranes?

The coverage of the LATICRETE family of waterproofing products varies, so please see the coverage estimates below for each individual product:

HYDRO BAN® XP
- One full unit consists of 5 gallons (19 liters) of HYDRO BAN^{® XP} liquid and will cover approximately 250 ft²(23.2m²).
- One mini unit consists of 1 gallon (3.8 liters) of HYDRO BAN XP liquid to cover approximately 50 ft²(4.65m²).
HYDRO BAN®
- One full unit consists of 5 gallons (19 liters) of HYDRO BAN^® liquid and will cover approximately 250 ft²(23.2m²).
- One mini unit consists of 1 gallon (3.8 liters) of HYDRO BAN liquid to cover approximately 50 ft²(4.65m²).
9235 Waterproofing Membrane
- One full unit consists of 6 gallons (23 liters) of 9235 Waterproofing Membrane liquid and Waterproofing/Anti-Fracture Fabric and will cover approximately 300 ft²(27m²).
- One mini unit consists of 2 gallons (7.6 liters) of 9235 Waterproofing Membrane liquid and Waterproofing/Anti-Fracture Fabric to cover approximately 75 ft²(6.8m²).
HYDRO BAN Quick Cure
- A one gallon unit (3.8 liters) of HYDRO BAN Quick Cure will cover approximately 134 ft²(12.4m²).
HYDRO BAN Cementitious Waterproofing
- One 30 lb. bag (13.6 kg) of HYDRO BAN Cementitious Waterproofing mixed will cover approximately 120 ft²(11.2m²) at 40 mil (1mm) total thickness.
HYDRO BARRIER™ Plus
- One full unit consists of 5 gallons (19 liters) of HYDRO BARRIER Plus liquid will cover approximately 250 ft²(23.2m²).
- One small unit consists of 3.5 gallon (13.3 liters) of HYDRO BARRIER Plus liquid will cover approximately 175 ft²(16.2m²).
HYDRO BARRIER™
- One full unit consists of 3.5 gallons (13.3 liters) of HYDRO BARRIER liquid and Waterproofing/Anti-Fracture Fabric and will cover approximately 175 ft²(16.2m²).
- One mini unit consists of 1 gallon (3.8 liters) of HYDRO BARRIER liquid and Waterproofing/Anti-Fracture Fabric to cover approximately 50 ft²(4.6m²).
HYDRO BAN Sheet Membrane
- One large roll of HYDRO BAN Sheet Membrane will cover approximately 323 ft²(30m²).
- One small roll of HYDRO BAN Sheet Membrane will cover approximately 108 ft²(10m²).

To what substrates can HYDRO BAN® XP, HYDRO BAN, 9235 Waterproofing Membrane, HYDRO BAN Quick Cure, HYDRO BAN Cementitious Waterproofing, HYDRO BARRIER™ and HYDRO BARRIER be directly applied?

Substrates common to HYDRO BAN® XP, HYDRO BAN, 9235 Waterproofing Membrane, HYDRO BAN Quick Cure, HYDRO BAN Cementitious Waterproofing, HYDRO BARRIER™ Plus and HYDRO BARRIER are clean, structurally sound concrete, exterior glue plywood (interior applications only), masonry surfaces, gypsum wallboard (interior applications only), cement backer boards, cement mortar beds, concrete and brick masonry, and cement plasters. For a more complete list of suitable substrates, please refer to the product data sheets of the individual LATICRETE membrane. For applications in exterior conditions over occupied areas or applications where tile or stone will be installed over exterior, wood-framed decks - see Plaza and Deck System (DS 290.0).

How soon can I typically install 9235 Waterproofing Membrane over...?

New concrete - minimum 14 days at 70°F (21°C)
Latex mortar beds - next day at 70°F (21°C)
Leveling or patching materials - allow a full 72 hour cure time at 70°F (21°C).

*NOTE: Most importantly for all substrates above; the substrate moisture content must not exceed 5 lbs./1,000 ft²/24 hours (283µg/s•m²) when tested using the Calcium Chloride test (ASTM F1869) or 75% Relative Humidity (RH) when tested with moisture probes (ASTM F2170). Cooler temperatures require longer cure time.

How soon can I install HYDRO BAN® XP over...?

New concrete - minimum 14 day cure time at 70°F (21°C).
Latex mortar beds - allow a full 72 hour minimum cure time at 70°F (21°C).
Leveling or patching materials - allow a full 72 hour minimum cure time at 70°F (21°C).

*NOTE: Most importantly for all substrates above; the substrate moisture content must not exceed 5 lbs./1,000 ft²/24 hours (283µg/s•m²) when tested using the Calcium Chloride test (ASTM F1869) or 75% Relative Humidity (RH) when tested with moisture probes (ASTM F2170). Cooler temperatures require longer cure time.

How soon can I install HYDRO BAN® over...?

How soon can I install HYDRO BARRIER® Plus over...?

How soon can I install HYDRO BARRIER® over...?

How soon can I install HYDRO BAN® Cementitious Waterproofing Membrane over...?

New concrete - minimum 14 day cure time at 70°F (21°C).
Latex mortar beds - allow a minimum 48 hour cure time at 70°F (21°C).
Leveling or patching materials - allow a minimum 48 hour cure time at 70°F (21°C).

How soon can I install HYDRO BAN® Quick Cure over...?

New concrete - minimum 24 hour cure time at 70°F (21°C) or as soon as you can walk on the concrete**.
Latex mortar beds - allow a minimum 1 hour cure time at 70°F (21°C) or as soon as the mortar bed is hard enough to walk on**.
Leveling or patching materials - allow a minimum 1 hour cure time at 70°F (21°C) or as soon as the mortar bed is hard enough to walk on**.

**NOTE: Hardness of substrate to be determined by general contractor or the responsible project design professional.

How soon can I flood test 9235 Waterproofing Membrane...?

Seven days after installation at 70°F (21°C). Cooler temperatures require longer cure time.

How soon can I flood test HYDRO BAN®?

Allow the second liquid coat of HYDRO BAN® to dry to a uniform olive green color and then allow a minimum of two full hours cure at 70°F (21°C) prior to commencing flood test. For temperatures ranging between 50° and 69°(10°-21°C) allow the second coat of HYDRO BAN to dry to a uniform olive green color and then wait for a minimum of 24 hours prior to commencing flood test.

How soon can I flood test HYDRO BAN® Quick Cure?

Allow the second liquid coat of HYDRO BAN® Quick Cure to dry a minimum of 15 minutes at 70°F (21°C) prior to commencing flood test. For temperatures ranging between 50° and 69°(10°-21°C) allow for an extra 15 minutes cure time prior to commencing flood test.

How soon can I flood test HYDRO BARRIER™?

Allow HYDRO BARRIER™ to dry a minimum of 24 hours at 70°F (21°C) prior to commencing flood test. For temperatures ranging between 45° and 69°(5°-21°C) allow for 3 days of curing prior to commencing flood test.

How soon can I flood test HYDRO BAN® Cementitious Waterproofing?

Allow HYDRO BAN® Cementitious Waterproofing to cure fully, typically 2 hours after final cure at 70°F (21°C) and 50% RH prior to commencing flood test. For temperatures ranging between 50° and 69°(10°-21°C) allow 24 hours after final cure prior to commencing flood test.

How soon can I flood test HYDRO BAN^® Sheet Membrane?

Allow the thin-set used to adhere HYDRO BAN® Sheet Membrane to cure a minimum of 24 hours at 70°F (21°C) and 50% RH prior to commencing flood test. Cold and/or wet conditions will require a longer cure time.

What adhesives are acceptable for installing tile over HYDRO BAN®, 9235 Waterproofing Membrane, HYDRO BAN Quick Cure, HYDRO BAN Cementitious Waterproofing, HYDRO BARRIER, and HYDRO BAN Sheet Membrane?

Some options are:
LATAPOXY® 300 Adhesive (for chemical resistant installations and the installation of moisture sensitive stone)*
257 Titanium
254 Platinum
254R Platinum Rapid
MULTIMAX LITE
TRI-LITE

*NOTE: Requires 9235 Waterproofing Membrane to cure for a full 7 days prior to installing with LATAPOXY 300. Allow HYDRO BAN^® to cure for 2 hours after the membrane has completely dried to the touch at 70°F (21°C), prior to installing tile or stone with LATAPOXY 300 Adhesive. Allow HYDRO BAN Quick Cure to cure for 30 minutes at 70°F (21°C), prior to installing tile or stone with LATAPOXY 300 Adhesive. Allow HYDRO BARRIER to cure for 24 hours at 70°F (21°C), prior to installing tile or stone with LATAPOXY 300 Adhesive. Allow HYDRO BAN Cementitious Waterproofing to cure for 2 hours at 70°F (21°C), prior to installing tile or stone with LATAPOXY 300 Adhesive. Tile can be installed on HYDRO BAN Sheet Membrane immediately after installation with LATAPOXY 300 Adhesive or any suitable tile installation mortar.

What approvals are available for 9235 Waterproofing Membrane?

What approvals are available for HYDRO BAN®?

What is the warranty on LATICRETE Membranes?

HYDRO BAN®, 9235 Waterproofing Membrane and HYDRO BAN Sheet Membrane are components of the LATICRETE Lifetime Tile & Stone System Warranty, the LATICRETE 25 Year Tile & Stone System Warranty, and the LATICRETE 10 Year Tile & Stone System Warranty when using a full LATICRETE System as outlined in the appropriate LATICRETE Systems Warranty.

MVIS™ Air & Water Barrier is a component of the LATICRETE 15 Year Tile & Stone System Warranty for Steel or Wood Framed Exterior Facades (DS 230.15).

HYDRO BARRIER is a component of the LATICRETE 5 Year Tile & Stone System Warranty for Steel or Wood Framed Exterior Facades (DS 230.05).

Every LATICRETE product is backed by the LATICRETE Product Warranty (DS 230.13) when used solely as an individual component of a tile or stone installation, when used with LATICRETE products not listed on the warranty document, or when used with competitor's products.

Will HYDRO BAN®, 9235 Waterproofing Membrane, HYDRO BAN Quick Cure, HYDRO BAN Cementitious Waterproofing, HYDRO BARRIER™, or HYDRO BAN Sheet Membrane control moisture vapor or water from entering the underside of the tile system due to negative hydrostatic pressure or excessive moisture content?

No! HYDRO BAN®, 9235 Waterproofing Membrane, HYDRO BAN Quick Cure, HYDRO BAN Cementitious Waterproofing, HYDRO BARRIER™, and HYDRO BAN Sheet Membrane are designed to contain water from the positive side only. The use of these membranes is not recommended where negative hydrostatic pressure or excessive vapor transmission exists from the back side exist. When a moisture vapor reduction membrane is required, use LATICRETE NXT™ Vapor Reduction Coating, LATICRETE® SUPERCAP® Moisture Vapor Control or SPARTACOTE™ Moisture Vapor Barrier prior to installation of the finished floor surface.

HYDRO BAN Sheet Membrane is a vapor retarder and is ideal for use as the waterproofing and vapor barrier in steam room/steam shower applications. Refer to the product data sheet for more information.

Can I use a mastic to install tile over a waterproofing membrane?

No. A latex fortified thin-set (e.g. 257 Titanium, 254 Platinum, etc...) or large, heavy tile mortar (e.g. MULTIMAX LITE), which complies with ANSI A118.4, A118.11 or A118.15 is required to properly bond tile or stone to a waterproofing membrane. An ANSI A118.3 compliant, full spread epoxy adhesive (LATAPOXY 300 Adhesive) may also be used.

How long can I leave a LATICRETE® membrane exposed before covering it?

HYDRO BAN®, 9235 Waterproofing Membrane, HYDRO BAN Quick Cure, HYDRO BAN Cementitious Waterproofing and HYDRO BARRIER™ must be covered by tile, stone, or other suitable finish material within 30 days. However, if the finish material is not yet available for installation, a skim coat of a latex fortified thin-set (e.g. 257 Titanium, 254 Platinum, etc...) will help protect the installation until the veneer finish material is available. The installation of the tile, stone or other suitable material can take place onto the hardened skim coat.

HYDRO BAN Sheet Membrane has no restrictions for exposure time but must be protected from excessive foot traffic, wheeled equipment, and other trades by using up to 3/4" (19mm) thick plywood or OSB protection over non-staining kraft paper.

What types of sealants are compatible with LATICRETE® membranes?

Use LATASIL™, a neutral cure, 100% silicone sealant which conforms to the following ASTM C920 standards; Type S, Grade NS, Class 25, Use NT, Use I, Use M, Use G. LATASIL also passes ASTM C794 Adhesion Properties.

How do I treat the drains when using a LATICRETE® Waterproofing Membrane?

You should use a 2-part clamping ring style drain (per ASME 112.6.3), a HYDRO BAN® Linear Drain or a HYDRO BAN Bonding Flange Drain.

For a 2-part clamping ring assembly, HYDRO BAN^®, 9235 Waterproofing Membrane, HYDRO BARRIER, or HYDRO BAN Sheet Membrane must be installed down into the drain assembly and clamped down between the clamping ring of the drain. Once the waterproofing membrane is dry to the touch, use LATASIL™ and put a continuous bead of sealant between the waterproofing membrane and the clamping ring before bolting down the clamping ring.

When using a LATICRETE Linear Drain, apply the HYDRO BAN, 9235 Waterproofing Membrane or HYDRO BARRIER onto the top flange of the HYDRO BAN Linear Drain to maintain continuity of the waterproofing from the mortar bed or HYDRO BAN Pre-Sloped Linear Shower Pan onto the drain flange. When using HYDRO BAN Sheet Membrane with a HYDRO BAN Linear Drain, apply two coats of HYDRO BAN to the top flange of the HYDRO BAN Linear Drain and allow to dry. When the HYDRO BAN is dry, install the HYDRO BAN Sheet Membrane from the mortar bed or HYDRO BAN Pre-Sloped Linear Shower Pan onto the drain flange.

When using a LATICRETE Bonding Flange Drain, apply the HYDRO BAN, 9235 Waterproofing Membrane or HYDRO BARRIER onto the top flange of the HYDRO BAN Linear Drain to maintain continuity of the waterproofing from the mortar bed or HYDRO BAN Pre-Sloped Linear Shower Pan onto the drain flange.

Can I install vinyl tile over HYDRO BAN®, 9235 Waterproofing Membrane, HYDRO BAN Quick Cure, or HYDRO BARRIER™?

Yes - after the HYDRO BAN®, 9235 Waterproofing Membrane, HYDRO BAN Quick Cure, HYDRO BARRIER™ is installed and allowed to dry, use a latex based vinyl adhesive to adhere the vinyl tile to the membrane. Ensure that the adhesive contains no solvents. If there is a question as to the compatibility of the vinyl adhesive and the membrane, apply a continuous 1/8" (3mm) thick coating of a LATICRETE liquid latex thin-set mortar (e.g. 257 Titanium, 254 Platinum, etc...) to the membrane and allow to harden. Then install the vinyl flooring.

Can I install HYDRO BAN®, 9235 Waterproofing Membrane, HYDRO BAN Quick Cure, HYDRO BARRIER™, HYDRO BAN Cementitious Waterproofing, or HYDRO BAN Sheet Membrane directly over plywood in exterior applications?

No! HYDRO BAN®, 9235 Waterproofing Membrane, HYDRO BAN Quick Cure, HYDRO BARRIER™, HYDRO BAN Cementitious Waterproofing, and HYDRO BAN Sheet Membrane are not intended for this installation. The LATICRETE Plaza and Deck System must be used for this type of installation.

When can I install tile over HYDRO BAN®, 9235 Waterproofing Membrane, HYDRO BAN Quick Cure, HYDRO BARRIER™, HYDRO BAN Cementitious Waterproofing, or HYDRO BAN Sheet Membrane?

When using HYDRO BAN®, 9235 Waterproofing Membrane or HYDRO BARRIER™, tile can be installed as soon as the final liquid coat is completely dry to the touch. When using HYDRO BAN Sheet Membrane, tile can be installed as soon as it is installed. However, use caution when moving on a floor with freshly installed HYDRO BAN Sheet Membrane so as not to cause movement of the membrane.

If flood testing is required for the installation, please refer to the FAQ listed above for flood testing the LATICRETE membrane being used;

When should you use a waterproofing membrane?

Related Documents:

Can you tile over a waterproofing membrane?

Related Documents:

Is a waterproofing membrane necessary?

Related Documents:

How do I install HYDRO BAN®?

Related Documents:

How do I install HYDRO BAN® XP?

Related Documents:

How do I install HYDRO BAN® Quick Cure?

Related Documents:

How do I install HYDRO BAN® Cementitious Waterproofing?

Related Documents:

How do I install HYDRO BARRIER™ Plus?

Related Documents:

How do I install HYDRO BARRIER™?

Related Documents:

How do I install HYDRO BAN Sheet Membrane?

Related Documents:

What is the coverage of LATICRETE® Waterproofing Membranes?

Related Documents:

To what substrates can HYDRO BAN® XP, HYDRO BAN, 9235 Waterproofing Membrane, HYDRO BAN Quick Cure, HYDRO BAN Cementitious Waterproofing, HYDRO BARRIER™ and HYDRO BARRIER be directly applied?

Related Documents:

How soon can I typically install 9235 Waterproofing Membrane over...?

Related Documents:

How soon can I install HYDRO BAN® XP over...?

Related Documents:

How soon can I install HYDRO BAN® over...?

Related Documents:

How soon can I install HYDRO BARRIER® Plus over...?

Related Documents:

How soon can I install HYDRO BARRIER® over...?

Related Documents:

How soon can I install HYDRO BAN® Cementitious Waterproofing Membrane over...?

Related Documents:

How soon can I install HYDRO BAN® Quick Cure over...?

Related Documents:

How soon can I flood test 9235 Waterproofing Membrane...?

Related Documents:

How soon can I flood test HYDRO BAN®?

Related Documents:

How soon can I flood test HYDRO BAN® Quick Cure?

Related Documents:

How soon can I flood test HYDRO BARRIER™?

Related Documents:

How soon can I flood test HYDRO BAN® Cementitious Waterproofing?

Related Documents:

How soon can I flood test HYDRO BAN® Sheet Membrane?

Related Documents:

What adhesives are acceptable for installing tile over HYDRO BAN®, 9235 Waterproofing Membrane, HYDRO BAN Quick Cure, HYDRO BAN Cementitious Waterproofing, HYDRO BARRIER, and HYDRO BAN Sheet Membrane?

Related Documents:

What approvals are available for 9235 Waterproofing Membrane?

Related Documents:

What approvals are available for HYDRO BAN®?

Related Documents:

What is the warranty on LATICRETE Membranes?

Related Documents:

Will HYDRO BAN®, 9235 Waterproofing Membrane, HYDRO BAN Quick Cure, HYDRO BAN Cementitious Waterproofing, HYDRO BARRIER™, or HYDRO BAN Sheet Membrane control moisture vapor or water from entering the underside of the tile system due to negative hydrostatic pressure or excessive moisture content?

Related Documents:

Can I use a mastic to install tile over a waterproofing membrane?

Related Documents:

How long can I leave a LATICRETE® membrane exposed before covering it?

Related Documents:

What types of sealants are compatible with LATICRETE® membranes?

Related Documents:

How do I treat the drains when using a LATICRETE® Waterproofing Membrane?

Related Documents:

Can I install vinyl tile over HYDRO BAN®, 9235 Waterproofing Membrane, HYDRO BAN Quick Cure, or HYDRO BARRIER™?

Can I install HYDRO BAN®, 9235 Waterproofing Membrane, HYDRO BAN Quick Cure, HYDRO BARRIER™, HYDRO BAN Cementitious Waterproofing, or HYDRO BAN Sheet Membrane directly over plywood in exterior applications?

Related Documents:

When can I install tile over HYDRO BAN®, 9235 Waterproofing Membrane, HYDRO BAN Quick Cure, HYDRO BARRIER™, HYDRO BAN Cementitious Waterproofing, or HYDRO BAN Sheet Membrane?

Related Documents:

About Us

Our Online Tools

Contact Us

About Us

Our Online Tools

Contact Us

How soon can I flood test HYDRO BAN^® Sheet Membrane?